DigiDesign MachineControl Especificaciones descargar pdf (Pagina 36)

MachineControl Guide32

Entering a New Byte Code

As the Sony P2 protocol continues to expand,

more manufacturers add specific byte code com-

mands that may be listed in the current byte

code list. Pro Tools lets you create entirely new,

custom byte codes. This lets you enter addi-

tional byte commands as needed to support new

features as they are added to decks.

Choosing a Record Protocol

The Machine Track Arming window provides

the following two choices for configuring the re-

cording protocol of the target deck:

Auto Edit

This mode is a highly accurate way to ensure

that the target deck will record only within the

boundaries of an on-screen selection. (If your

deck does not support Auto Edit, use Punch

In/Punch Out, as explained below.)

In Auto Edit mode, the record start/end times

are downloaded to the target deck (along with

any pre- or post-roll), and the deck is responsible

for performing the insert punch in/out at the

specified times (see “Rules for On-Screen Selec-

tions” on page 33 for details).

Because this protocol removes the vagaries of

CPU timing from the remote recording process,

Auto Edit is frame-accurate. It is also the best

way to ensure that your machine will punch out

correctly and avoid accidental erasure of audio,

even in the event of a CPU error.

Punch In/Out

This mode uses Pro Tools to control the process

of punch in/out. Instead of downloading the

punch points (as in Auto Edit), Pro Tools actu-

ally performs them during the record pass. Be-

cause serial communication has inherent de-

lays, timing with Punch In/Punch Out mode

cannot guarantee frame-accuracy (though it will

almost always be within 2 to 3 frames).

Choosing a Record Mode

The Machine Track Arming window provides

two choices for Record mode:

Insert

Insert mode is used to perform insert editing

(punching in individual tracks) where one or

more audio tracks is replaced by new material

and the video material is retained.

Assemble

Use Assemble mode when you want to:

◆ Begin recording program onto a completely

blank tape (unformatted)

– or –

◆ Append program to the remainder of a tape

which already has program you want to keep

Assemble mode is not appropriate for audio lay-

backs to video masters.

Assemble mode should be used carefully be-

cause it arms all tracks on the target deck for re-

cording—including the video track, time code

track and control track. When performing an

Assemble edit, all material on all tracks after the

edit in point will be replaced. Because a break in

the control track will result at the edit out point,

any remaining program material after an Assem-

ble edit may be unusable.

Entering a new byte code

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 51 52

Comentarios a estos manuales

Sin comentarios

Whirlpool ELVD 6250/IN Instrucciones de uso (13 paginas)

Marca: Whirlpool | Categoria: Ovens | Tamaño: 4.40 MB |

Tabla de contenidos

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION

SAFEGUARDING THE ENVIRONMENT

CLEANING

DECLARATION OF CONFORMITY

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

MAINTENANCE

REPLACING THE OVEN LAMP

INSTRUCTIONS FOR OVEN USE

CONTROL PANEL DESCRIPTION

OVEN OPERATION

COOKTOP OPERATION

1 2 3 4 5

Setting end of cooking time

KEY-LOCK

COOKING TABLE

How to read the cooking table

RECOMMENDED USE AND TIPS

Más productos y manuales para Hornos Whirlpool

Modelos	Tipo de documento
AKZM 750/IX	Instrucciones de uso Whirlpool AKZM 750/IX Instruction for Use, 20 paginas
AKP 461/IX	Instrucciones de uso Whirlpool AKP 461/IX Instruction for Use, 94 paginas
AKP 256/NA	Instrucciones de uso Whirlpool AKP 256/NA Instruction for Use, 26 paginas
EMDK7 6638 PT	Manual de uso y cuidado Whirlpool EMDK5 5438 PT Health and safety, 8 paginas
AKPM 658/IX	Instrucciones de uso Whirlpool AKPM 658/IX Instruction for Use [da] , 11 paginas
EMV 6260/IN	Instrucciones de uso Whirlpool EMV 6260/IN Instruction for Use [fr] , 14 paginas
FT 850.1 (OW) /HA S	Instrucciones de uso Whirlpool FT 850.1 (AN) /HA S Instruction for Use [en] , 72 paginas
OK 1037EL DP.20 X/HA	Instrucciones de uso Whirlpool OK 1037EL DP.20 X/HA Instruction for Use, 64 paginas
AKP 158/IX	Instrucciones de uso Whirlpool AKP 158/IX Instruction for Use [de] [es] [fr] [it] [nl] [pt] , 12 paginas
AKZM 833/IX	Instrucciones de uso Whirlpool AKZM 833/IX Instruction for Use [nl] , 48 paginas
FI 20 K.A IX	Instrucciones de uso Whirlpool FI 20 K.A IX Instruction for Use, 72 paginas
BLCE 7103/PT	Instrucciones de uso Whirlpool BLCE 7103/PT Instruction for Use [da] , 23 paginas
AKP 255/IX	Instrucciones de uso Whirlpool AKP 255/IX Instruction for Use [sv] , 9 paginas
AKZM 740/IX	Instrucciones de uso Whirlpool AKZM 740/IX Instruction for Use [es] , 21 paginas
MH 99.1 (BK) /HA S	Instrucciones de uso Whirlpool MH 99.1 (BK) /HA S Instruction for Use, 68 paginas
MBI 700 S	Instrucciones de uso Whirlpool MBI 700 S Instruction for Use [da] , 20 paginas
AKP 444/MR	Instrucciones de uso Whirlpool AKP 444/MR Instruction for Use, 11 paginas
AKZ 560/WH	Instrucciones de uso Whirlpool AKZ 560/WH Instruction for Use [de] [en] [fr] [nl] , 22 paginas
AKZ 389 IX	Instrucciones de uso Whirlpool AKZ 389 IX Instruction for Use [et] , 8 paginas
FK 83 X S	Instrucciones de uso Whirlpool FK 83 X S Instruction for Use [de] , 60 paginas