MachineControl Guide24

Identifying your Machine

If Pro Tools does not recognize your machine,

you can use the generic1 personality. However,

you should try a few test laybacks, using backup

tapes or other non-vital material, to determine

the best settings for your system.

Requesting additional machine proﬁles for

Track Arming

If you would like Digidesign to facilitate auto-

detection of a specific machine in an upcoming

release, you can e-mail a request, including the

manufacturer and machine model to post-

[email protected].

Conﬁguring the Number of Tracks

Use the Record Tracks pop-up to specify the

number of record tracks for the target deck. The

maximum number of supported record tracks is

eight. If you specify more record tracks than the

machine possesses, they will be ignored.

If you are using a “generic” device personality,

set the number of tracks to eight. Be sure to dou-

ble-check track arming, as machines differ in

how they will map arming commands.

After the number of record tracks is specified in

the Record Tracks popup, the record-arming

track buttons are active. The Record Arm but-

tons will be named with the appropriate ma-

chine-specific track name. The button text dis-

plays in red when armed.

Choosing a Record Protocol

The following two choices are available for con-

ﬁguring the recording protocol to be utilized by

the target deck:

Auto Edit

This mode is a highly accurate way to ensure

that the target deck will record only within the

boundaries of an on-screen selection. (If your

deck does not support Auto Edit, use Punch

In/Punch Out, explained below.)

In this mode, the record start/end times are

downloaded to the target deck (along with any

pre- or post-roll), and the deck is responsible for

performing the insert punch in/out at the spec-

ified times (see “Rules for On-Screen Selections”

on page 25 for details).

Because this protocol removes the vagaries of

CPU timing from the remote recording process,

Auto Edit is frame-accurate. It is also the best

way to ensure that your machine will punch out

correctly and avoid accidental erasure of audio,

even in the event of a CPU error.

Punch In/Out

This mode uses Pro Tools to control the process

of punch in/out. Instead of downloading the

punch points (as in Auto Edit), Pro Tools actu-

ally performs them during the record pass. Be-

cause serial communication has inherent de-

lays, timing with Punch In/Punch Out mode

cannot guarantee frame-accuracy (though it will

almost always be within 2 to 3 frames).

If you are using the generic1 device person-

ality, be sure to double-check record behav-

ior using non-essential tapes before at-

tempting to use MachineControl’s remote

track arming modes.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 45 46

Comentarios a estos manuales

Sin comentarios

Patriot Memory PSD22G667SK manuales

Manuales del propietario y guías del usuario para Los módulos de memoria Patriot Memory PSD22G667SK.
Ofrecemos 1 manuales en pdf Patriot Memory PSD22G667SK para descargar gratis por tipos de documentos: Ficha de datos

Modelos	Tipo de documento
PGS34G1600ELKA	Ficha de datos Patriot Memory 4GB DDR3 PC3-12800 Dual Channel DIMM Kit, 1 paginas
PVS34G1333LLKN	Ficha de datos Patriot Memory 4GB DDR3 PC3-10666 DIMM Kit, 1 paginas
PSD21G800K	Ficha de datos Patriot Memory PSD21G800K memory module, 1 paginas
PSA32G10662S	Ficha de datos Patriot Memory 2GB DDR3 SODIMM Kit, 1 paginas
PSD21G6672S	Ficha de datos Patriot Memory PSD21G6672S memory module, 1 paginas
PSD24G667EFBK	Ficha de datos Patriot Memory DDR2 4GB (2 x 2GB) CL5 PC2-5300 (667MHz) ECC Fully Buffered DIMM, 1 paginas
PSD22G533SK	Ficha de datos Patriot Memory PSD22G533SK memory module, 1 paginas
PSD38G1333SK	Ficha de datos Patriot Memory 8GB PC3-10600, 1 paginas
PSD24G667KH	Ficha de datos Patriot Memory DDR2 4GB (2 x 2GB) CL5 PC2-5300 (667MHz) DIMM Kit, 1 paginas
PSD1G400	Ficha de datos Patriot Memory PSD1G400 memory module, 1 paginas
PSD1G40016S	Ficha de datos Patriot Memory PSD1G40016S memory module, 1 paginas
PV234G1800LLKN	Ficha de datos Patriot Memory Viper II 4GB DDR3 DC Kit, 1 paginas
PVS34G1800LLKN	Ficha de datos Patriot Memory 4GB DDR3 PC3-14400 DIMM Kit, 1 paginas
PSA24G800EFBK	Ficha de datos Patriot Memory 4GB DDR2 DIMM Kit, 1 paginas
PVS32G1600LLKN	Ficha de datos Patriot Memory 2GB DDR3 PC3-12800 DC Kit, 1 paginas
PSA28G800EFBK	Ficha de datos Patriot Memory 8GB DDR2 DIMM Kit, 1 paginas
PSD21G8002-I	Ficha de datos Patriot Memory DDR2 1GB CL5 PC2-6400 (800MHz) Intel DIMM, 1 paginas
PSD36G1600KH	Ficha de datos Patriot Memory 3GB DDR3 PC3-12800 TC Kit, 1 paginas
PSD21G800K-I	Ficha de datos Patriot Memory DDR2 1GB (2 x 512MB) CL5 PC2-6400 (800MHz) Intel DIMM Kit, 1 paginas
PSD32G10662	Ficha de datos Patriot Memory DDR3 2GB CL7 PC3-8500 (1066MHz) 2 Rank DIMM, 1 paginas

DigiDesign MachineControl Guía de usuario Pagina 28

Comentarios a estos manuales

Patriot Memory PSD22G667SK manuales

Patriot memory PSD22G667SK Ficha de datos (1 paginas)

Tabla de contenidos

Más productos y manuales para Los módulos de memoria Patriot Memory

DigiDesign MachineControl Guía de usuario Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Software DigiDesign MachineControl

Patriot Memory PSD22G667SK manuales

Patriot memory PSD22G667SK Ficha de datos (1 paginas)

Tabla de contenidos

Más productos y manuales para Los módulos de memoria Patriot Memory