DigiDesign MachineControl Especificaciones Pagina 68
- Pagina / 98
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SYNC I/O Guide64
6 When you reach a value that matches the
sticker’s value, stop scrolling and press Set. The
LED Time Code Display will return to showing
time code numbers. Your SYNC I/O is now prop-
erly calibrated.
The next time you press Set, the LED Time Code
Display will again show O5C CAL. If you then
press the Down switch, you’ll disengage the Os-
cillator Calibration parameter name. To change
the setting once again, you’ll need to repeat
steps 1 through 6.
Restoring Factory Settings
SYNC I/O can be reset to its default factory set-
tings.
To reset all parameters to default settings:
1 Switch off power to SYNC I/O and wait at least
10 seconds.
2 Hold down the Up and Down front panel
switches and turn on power to SYNC I/O. Do not
release the Up and Down switches until the dis-
play reads FAC-CFG.
Factory Default Settings
The following table lists the default settings of
each parameter.
Resetting factory settings does not reset the
SYNC I/O oscillator. See “Calibrating the
SYNC I/O Oscillator” on page 63 for infor-
mation.
SYNC I/O Defaults
Parameter Name Default
Set Generator Start Time
00:00:00:00
Digital Reference
AES/EBU
Sample Freq (Rate)
44.1 kHz
VITC Insertion
On
Pull Rates
Off
Base Clock
Session (1x Word)
(VITC) Reader Line
All
(VITC) Generate Line
14–16
Window Burn On/Off
On (Enabled)
Freewheel Duration
8 frames
LTC Output gain
3 dBu
Servo gain
–001
Pitch Hold
Off
Bi-Phase Pulse-per-frame
0100
Bi-Phase Signal
A Lead B
Video System/Format
NTSC
Idle MTC Enabled
On
Window Burn options:
Enabled
Size: Large
Ver tical Position: 20%
from Bottom
Horizontal Position: Center
Color: White on Black
background
Variable Speed Offset
(VSO)
Off
- SYNC I/O Guide 1
- Chapter 1. Introduction 3
- Chapter 4. Using SYNC I/O 3
- Introduction 5
- SYNC I/O Features 6
- System Requirements 7
- Digidesign Registration 8
- About the Pro Tools Guides 8
- About www.digidesign.com 9
- SYNC I/O Guide6 10
- Installation and Configuration 11
- Clock for Pro Tools 12
- Audio Interfaces 12
- Connecting Slave Clock for 13
- Pro Tools 13
- MachineControl 14
- Time Code Connections to 15
- Machines, Decks, and Other 15
- Synchronization and 15
- Connecting LTC 16
- Connecting Word Clock Devices 16
- Connecting AES/EBU Devices 16
- Software Installation 17
- Configuring Pro Tools 18
- SYNC I/O 18
- Configuring SYNC I/O in the 19
- Locked and Speed Cal LEDs 20
- Positional Reference 20
- Sample Rate 21
- Time Code Rate 21
- Feet+Frame Rate 21
- MachineControl Configuration 22
- Software Configuration for 22
- SYNC I/O Setup Software 22
- Configuring Pro Tools 23
- Updating SYNC I/O Firmware 23
- Firmware Messages 24
- Troubleshooting 25
- SYNC I/O Guide22 26
- SYNC I/O Front Panel 27
- Sample Rate LEDs 28
- Generator/Parameter Controls 28
- Time Code Display 28
- Positional Reference Switch 29
- Frame Rate Switch 29
- Status LEDs 29
- SYNC I/O Back Panel 30
- Video In/Out 31
- LTC In/Out 31
- AES/EBU In/Out 31
- SYNC I/O Guide30 34
- Bi-Phase/Tach Parameters 35
- Generator/Bi-Phase Preset 35
- Variable Speed Override (VSO) 35
- SYNC I/O Guide32 36
- Using SYNC I/O 37
- Available from/in: 38
- Pro Tools Front Panel 38
- SYNC I/O Setup 38
- Software Utility 38
- Front Panel 39
- Generator/Parameter 39
- Switches 39
- Clock References and Options 40
- Digital Clock 41
- LTC and Clock Reference 42
- Pilot Tone 43
- Regenerating 44
- Freewheel Duration 47
- VITC and Positional Reference 47
- Reference 48
- Serial Time Code 49
- SYNC I/O Guide46 50
- Read/Regeneration Mode 51
- Generator Preset Mode 52
- LTC Generation/Regeneration 53
- VITC Generation/Regeneration 54
- Internal VITC Generation 55
- SYNC I/O Guide52 56
- Generating a Window Burn 57
- SYNC I/O Guide54 58
- Chapter 4: Using SYNC I/O 55 59
- SYNC I/O Guide56 60
- Controls 61
- SYNC I/O Guide58 62
- VITC Generate Lines 63
- Window Dub/Burn 63
- Freewheel Length/Duration 63
- LTC Output Level/Gain 64
- Servo Gain 64
- Pitch Memory/Hold 64
- Bi-Phase/Tach Input Signal 65
- Video Format/System 65
- MTC Idle Mute 65
- Using Fader Start 66
- Calibrating the SYNC I/O 67
- Oscillator 67
- Restoring Factory Settings 68
- Managing and Selecting Video 69
- SYNC I/O Guide66 70
- Video and VITC Signals 71
- Auto-Switch LTC/VITC 72
- LTC Signals 72
- Digital Clock Signal Types 73
- Bi-Phase/Tach 74
- SYNC I/O Guide72 76
- Technical Specifications 77
- Rear Panel Connectors 80
- Bi-Phase/GPI/Pilot 86
- GPI Relay Outputs 88
- GPI (TTL)/MTC Outputs 89
- GPI (opto) Inputs 90
- Connector Pin Assignments 91
- SYNC I/O Serial Cable Pin 93
- Assignments 93
- Bi-phase/Tach/GPI/Pilot Port 93
- Interfacing Notes 93
- GPI Triggers 94
- GPI TTL WIring 94
Relacionado con productos y manuales para Software DigiDesign MachineControl
Software DigiDesign Command|8 Especificaciones
(126 paginas)
(126 paginas)
Software DigiDesign Pro Tools Especificaciones
(73 paginas)
(73 paginas)
Rollei 20849 manuels
Manuels d'utilisation et guides de l'utilisateur pour Trépieds Rollei 20849.
Nous fournissons des manuels en pdf 1 Rollei 20849 à télécharger gratuitement par type de document : Fiche technique
Comentarios a estos manuales