DigiDesign MachineControl Especificaciones descargar pdf (Pagina 79)

Appendix B: Technical Speciﬁcations 75

Shock 5 G max

Operating Temperature 32 to 131 degrees F (0 to 55 degrees C)

Storage Temperature -40 to 176 degrees F (-40 to 80 degrees C)

Relative Humidity 0 to 95%, non-condensing

Power Requirements Voltage: 85 to 264 VAC

Frequency: 47 to 63 Hz autoswitching

Wattage: 9.5 W typical, 30 W maximum

Connector: 3-pin, AC and ground (IEC

950:320;3.2.4)

Agency Compliance

Meets FCC Part 15 Class A limits, CD EN 55022A, CE EN 60950,

CE EN 55081:1, UL 1419 and CSA 22.2

General

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 97 98

SYNC I/O Guide 1
Chapter 1. Introduction 3
Chapter 4. Using SYNC I/O 3
Introduction 5
SYNC I/O Features 6
System Requirements 7
Digidesign Registration 8
About the Pro Tools Guides 8
About www.digidesign.com 9
SYNC I/O Guide6 10
Installation and Conﬁguration 11
Clock for Pro Tools 12
Audio Interfaces 12
Connecting Slave Clock for 13
Pro Tools 13
MachineControl 14
Time Code Connections to 15
Machines, Decks, and Other 15
Synchronization and 15
Connecting LTC 16
Connecting Word Clock Devices 16
Connecting AES/EBU Devices 16
Software Installation 17
Conﬁguring Pro Tools 18
SYNC I/O 18
Conﬁguring SYNC I/O in the 19
Locked and Speed Cal LEDs 20
Positional Reference 20
Sample Rate 21
Time Code Rate 21
Feet+Frame Rate 21
MachineControl Conﬁguration 22
Software Conﬁguration for 22
SYNC I/O Setup Software 22
Conﬁguring Pro Tools 23
Updating SYNC I/O Firmware 23
Firmware Messages 24
Troubleshooting 25
SYNC I/O Guide22 26
SYNC I/O Front Panel 27
Sample Rate LEDs 28
Generator/Parameter Controls 28
Time Code Display 28
Positional Reference Switch 29
Frame Rate Switch 29
Status LEDs 29
SYNC I/O Back Panel 30
Video In/Out 31
LTC In/Out 31
AES/EBU In/Out 31
SYNC I/O Guide30 34
Bi-Phase/Tach Parameters 35
Generator/Bi-Phase Preset 35
Variable Speed Override (VSO) 35
SYNC I/O Guide32 36
Using SYNC I/O 37
Available from/in: 38
Pro Tools Front Panel 38
SYNC I/O Setup 38
Software Utility 38
Front Panel 39
Generator/Parameter 39
Switches 39
Clock References and Options 40
Digital Clock 41
LTC and Clock Reference 42
Pilot Tone 43
Regenerating 44
Freewheel Duration 47
VITC and Positional Reference 47
Reference 48
Serial Time Code 49
SYNC I/O Guide46 50
Read/Regeneration Mode 51
Generator Preset Mode 52
LTC Generation/Regeneration 53
VITC Generation/Regeneration 54
Internal VITC Generation 55
SYNC I/O Guide52 56
Generating a Window Burn 57
SYNC I/O Guide54 58
Chapter 4: Using SYNC I/O 55 59
SYNC I/O Guide56 60
Controls 61
SYNC I/O Guide58 62
VITC Generate Lines 63
Window Dub/Burn 63
Freewheel Length/Duration 63
LTC Output Level/Gain 64
Servo Gain 64
Pitch Memory/Hold 64
Bi-Phase/Tach Input Signal 65
Video Format/System 65
MTC Idle Mute 65
Using Fader Start 66
Calibrating the SYNC I/O 67
Oscillator 67
Restoring Factory Settings 68
Managing and Selecting Video 69
SYNC I/O Guide66 70
Video and VITC Signals 71
Auto-Switch LTC/VITC 72
LTC Signals 72
Digital Clock Signal Types 73
Bi-Phase/Tach 74
SYNC I/O Guide72 76
Technical Speciﬁcations 77
Rear Panel Connectors 80
Bi-Phase/GPI/Pilot 86
GPI Relay Outputs 88
GPI (TTL)/MTC Outputs 89
GPI (opto) Inputs 90
Connector Pin Assignments 91
SYNC I/O Serial Cable Pin 93
Assignments 93
Bi-phase/Tach/GPI/Pilot Port 93
Interfacing Notes 93
GPI Triggers 94
GPI TTL WIring 94

Comentarios a estos manuales

Sin comentarios

DigiDesign MachineControl Especificaciones Pagina 79

Comentarios a estos manuales

Relacionado con productos y manuales para Software DigiDesign MachineControl